Vertical.Special Series

  • Optimizing to produce multi cavity products
  • High sensitive mold protection
  • Cycle time reduction by high speed pressure increasing
  • Securement of the operator's safety by dividing molding and taking out position.
  • Accurate control of high speed rotation by Servo Motor
  • Improvement of position repeatability by table lock pin system.
Injection Unit
Model VR30 VR60 VR85 VR110
Item Unit
Injection Unit type Vertical
Screw Type type A B A B A B A B
Screw Diameter mm 25 28 28 32 36 40 36 40
Shot Weight (PS) g 45 56 67 88 111 137 111 137
Shot Size cm³ 49 61.5 73.8 96.5 122 150 122 150
Injection Pressure kg/cm³ 2329 1857 1857 1422 1483 1201 1483 1201
Injection Rate cm³/sec 39 49 67 87 123 152 123 152
Plasticizing Capacity kg/hr 16 19 24 29 56 75 56 75
Screw Speed rpm 0~240 0~250 0~250 0~250
Clamping Unit
Model VR30 VR60 VR85 VR110
Item Unit Table Table Table Table
Clamping Unit type Vertical
Clamping System type Tie Bar
Clamping Force ton 30 60 85 110
Opening Stroke mm 260 280 250 300
Min. Mold Height mm 160 180 250 300
Max. Mold Height mm 420 460 500 600
Table Diameter mm 860 1000 1150 1300
Ejector Stroke mm 60 60 70 80
General
Model VR30 VR60 VR85 VR110
Item Unit
Heater Capacity kW 2.7 3.5 7.5 7.5
Pump Motor Capacity kW 7.5 11 18.5 18.5
Total Electric Capacity kW 11.4 15.7 33 33.8
Oil Tank Capacity ℓ 250 300 350 350
Machine Size (L x W x H) m 2.0ｘ1.4ｘ2.9[2.3] 2.0ｘ1.5ｘ3.2[2.6] 2.2ｘ1.6ｘ3.6[2.9] 2.2ｘ1.9ｘ4.0[3.2]
Machine Weight ton 3.2 3.5 4.7 7.0
Water Requirement ℓ/min 20 30 38 38
  • Shot Size = Cross sectional area of screw diameter x screw stroke
  • Shot weight = Shot size x material constant
  • Total wattage = Heater power + pump motor power + system power.
  • Water requirement is not considered mold cooling but considered only injection molding machine.
  • Above data can be changed according to the manufacturer's R&D plan without notice to the customer side
  • Option : Hybrid system
  • Optimizing to produce multi cavity products
  • High sensitive mold protection
  • Cycle time reduction by high speed pressure increasing
  • Securement of the operator's safety by dividing molding and taking out position.
  • Maximizing the operator's convenience by combining vertical clamping unit with horizontal injection unit.
  • Improvement of position repeatability by table lock pin system.
Injection Unit
Model VR30 VR60 VR85 VR110
Item Unit
Injection Unit type Vertical
Screw Type type A B A B A B A B
Screw Diameter mm 25 28 28 32 36 40 36 40
Shot Weight (PS) g 45 56 67 88 111 137 111 137
Shot Size cm³ 49 61.5 73.8 96.5 122 150 122 150
Injection Pressure kg/cm³ 2329 1857 1857 1422 1483 1201 1483 1201
Injection Rate cm³/sec 39 49 67 87 123 152 123 152
Plasticizing Capacity kg/hr 16 19 24 29 56 75 56 75
Screw Speed rpm 0~240 0~250 0~250 0~250
Clamping Unit
Model VR30 VR60 VR85 VR110
Item Unit Table Table Table Table
Clamping Unit type Vertical
Clamping System type Tie Bar
Clamping Force ton 30 60 85 110
Opening Stroke mm 260 280 250 300
Min. Mold Height mm 160 180 250 300
Max. Mold Height mm 420 460 500 600
Table Diameter mm 860 1000 1150 1300
Ejector Stroke mm 60 60 70 80
General
Model CS25 CS45 VR60H VR85H VR150H VR200H
Item Unit
Heater Capacity kW 2.2 5.8 5.8 6.9 7.5 11.95
Pump Motor Capacity kW 7.5 11 11 18.5 22 30
Total Electric Capacity kW 10.9 18 18 26.6 30.7 43.15
Oil Tank Capacity ℓ 200 300 300 350 350 600
Machine Size (L x W x H) m 1.9ｘ1.7ｘ2.0 2.6ｘ1.7ｘ2.1 3.1ｘ1.4ｘ2.0 3.3ｘ1.6ｘ2.0 3.7ｘ2.0ｘ3.1 4.1ｘ2.1ｘ3.2
Machine Weight ton 2.8 4.1 4.2 5.0 10.5 14
Water Requirement ℓ/min 20 30 30 38 44 60
  • Shot Size = Cross sectional area of screw diameter x screw stroke
  • Shot weight = Shot size x material constant
  • Total wattage = Heater power + pump motor power + system power.
  • Water requirement is not considered mold cooling but considered only injection molding machine.
  • Above data can be changed according to the manufacturer's R&D plan without notice to the customer side Option : Hybrid system
  • Optimizing to produce multi cavity products
  • High sensitive mold protection
  • Cycle time reduction by high speed pressure increasing
  • Securement of the operator's safety by dividing molding and taking out position.
  • Maximizing the operator's convenience by combining vertical clamping unit with horizontal injection unit.
  • Improvement of productivity and safety by moving slide platen (VS series)
Injection Unit
Model VS/VB30 VS/VB60 VS/VB85 VS/VB150 VS/VB220
Item Unit
Injection Unit type Vertical
Screw Type type A B A B A B A B A B
Screw Diameter mm 25 28 28 32 36 40 45 50 55 60
Shot Weight (PS) g 45 56 67 88 137 169 318 392 480 571
Shot Size cm³ 49 61.5 73.8 96.5 150 186 349 431 527 627
Injection Pressure kg/cm³ 2329 1857 1857 1422 1840 1491 1919 1554 1833 1540
Injection Rate cm³/sec 39 49 91 112 91 112 134 165 226 269
Plasticizing Capacity kg/hr 16 19 50 67 50 67 79 100 145 183
Screw Speed rpm 0~240 0~231 0~231 0~198 0~213
Clamping Unit
Model VS/VB30 VS/VB60 VS/VB85 VS/VB150 VS/VB220
Item Unit Slide/Bed Slide/Bed Slide/Bed Slide/Bed Slide/Bed
Clamping Unit type Vertical
Clamping System type Tie Bar
Clamping Force ton 30 60 85 150 220
Opening Stroke mm 260 280 250 330 300
Min. Mold Height mm 160 180 250 300 350
Max. Mold Height mm 420 460 500 630 650
Space Between Tiebar
(H x V)		 mm 270ｘ295
270ｘ270		 350ｘ350
350ｘ350		 330ｘ470
470ｘ330		 400ｘ460 460ｘ610
610ｘ450
Platen Size (H x V) mm 410ｘ435
410ｘ410		 520ｘ520
515ｘ515		 500ｘ640
640ｘ500		 625ｘ685
685ｘ625		 730ｘ890
890ｘ730
Slide Platen Size (H x V) mm 900ｘ265 1050ｘ340 1100ｘ460 1200ｘ460 1400ｘ600
Slide Platen Stroke mm 450 - 500 - 550 - 600 - 700 -
Ejector Stroke mm 60 60 65 80 110
General
Model VS/VB30 VS/VB60 VS/VB85 VS/VB150 VS/VB220
Item Unit
Heater Capacity kW 2.7 3.5 6.3 7.8 9.7
Pump Motor Capacity kW 7.5 11 18.5 22 30
Total Electric Capacity kW 11.4 15.7 26 31 40.9
Oil Tank Capacity ℓ 250 300 350 350 500
Machine Size (L x W x H) m 1.3ｘ1.8ｘ2.9[2.4]
1.3ｘ1.3ｘ2.9[2.3]		 1.6ｘ2.0ｘ3.2[2.6]
1.4ｘ1.4ｘ3.1[2.4]		 1.7ｘ2.0ｘ3.6[2.9]
1.5ｘ1.5ｘ3.5[2.8]		 1.8ｘ2.2ｘ4.5
1.8ｘ1.9ｘ4.6		 2.2ｘ2.6ｘ5.0[4.1]
2.2ｘ2.2ｘ5.0[4.0]
Machine Weight ton 3.2 3.6 4.3 7.5 10.5 10.0
Water Requirement ℓ/min 20 30 38 44 60
  • Shot Size = Cross sectional area of screw diameter x screw stroke
  • Shot weight = Shot size x material constant
  • Total wattage = Heater power + pump motor power + system power.
  • Water requirement is not considered mold cooling but considered only injection molding machine.
  • Above data can be changed according to the manufacturer's R&D plan without notice to the customer side
  • Option : Hybrid system
  • Optimizing to produce multi cavity products
  • High sensitive mold protection
  • Cycle time reduction by high speed pressure increasing
  • Securement of the operator's safety by dividing molding and taking out position.
  • Vertical type type clamp and horizontal type injection unit
  • Improvement of productivity and production stability by left & right slide plate system (VS series)
Injection Unit
Model VS/VB85H VS/VB150H VB180H VB350H
Item Unit
Injection Unit type Horizontal
Screw Type type A B A B A B A B
Screw Diameter mm 36 40 45 50 45 50 55 60
Shot Weight (PS) g 137 169 318 392 318 392 539 642
Shot Size cm³ 150 186 349 431 349 431 593 706
Injection Pressure kg/cm³ 1840 1491 1919 1554 1919 1554 1833 1540
Injection Rate cm³/sec 91 112 134 165 134 165 227 270
Plasticizing Capacity kg/hr 50 67 79 100 79 100 145 183
Screw Speed rpm 0~231 0~198 0~198 0~250
Clamping Unit
Model VS/VB85H VS/VB150H VB180H VB350H
Item Unit Slide/Bed Slide/Bed Bed Bed
Clamping Unit type Vertical
Clamping System type Tie Bar
Clamping Force ton 85 150 180 350
Opening Stroke mm 250 370 370 500
Min. Mold Height mm 250 250 330 380
Bottom Mold Height mm 150 150 170 250
Daylight mm 500 620 700 880
Space Between Tiebar
(H x V)		 mm 330ｘ470
470ｘ330		 400ｘ460
460ｘ400		 460ｘ400 1400ｘ450
Platen Size (H x V) mm 500ｘ640
640ｘ500		 625ｘ685
685ｘ325		 695ｘ635 1760ｘ810
Slide Platen Size (H x V) mm 1100ｘ460
-		 1200ｘ456
-		 - -
Ejector Stroke mm 60 80 80 120
General
Model VS/VB85H VS/VB150H VB180H VB350H
Item Unit
Heater Capacity kW 6.9 7.5 7.5 10
Pump Motor Capacity kW 18.5 22 22 37
Total Electric Capacity kW 26.6 30.7 30.7 50.2
Oil Tank Capacity ℓ 350 380 380 800
Machine Size (L x W x H) m 3.1ｘ2.0ｘ2.1 3.1ｘ2.2ｘ2.8 3.1ｘ2.2ｘ2.8 3.7ｘ2.2ｘ3.8
Machine Weight ton 4.8 6.8 7.0 16.0
Water Requirement ℓ/min 38 44 48.4 74
  • Shot Size = Cross sectional area of screw diameter x screw stroke
  • Shot weight = Shot size x material constant
  • Total wattage = Heater power + pump motor power + system power.
  • Water requirement is not considered mold cooling but considered only injection molding machine.
  • Above data can be changed according to the manufacturer's R&D plan without notice to the customer side
  • Option : Hybrid system

Low pressure injection molding machine

Injection

  • Inject the melted material into the mold using low pressure

Bolster & Moving Unit

  • Device to install bottom mold
  • Installed on the right side 1set & left side 1set from the center of injection M/C
  • Transferring the bolster left and right side by hydraulic motor

Low pressure injection molding machine

Structure

  • Clamping unit - Crown, Moving plate, Bolster, Rotary Plate, Oil Tank.

Features

  • Take advantage of strong point from vertical & horizontal machine
  • High speed movement and precise positioning of bottom platen by Servo motor.
  • Easy insert process by 90° rotation of top platen and realization of high speed cycle.

1 (one) cycle

  • Rising of top platen (mold open)
    • Bolster transferring left side
    • Descent of top side rotary platen
    • Ascent of top side rotary platen
    • Bolster transferring right side
    • Falling of top platen (mold close)
    • Injection unit forward
    • Injection
    • Injection unit backward